Chain for Forklifts

Forklift Chains - The life of the forklift lift chains could actually be lengthened with correct maintenance and care. Lubricating correctly is a great method to be able to extend the capability of this particular forklift component. It is essential to apply oil occasionally utilizing a brush or whatever lube application device. The frequency and volume of oil application has to be sufficient in order to prevent any rust discoloration of oil within the joints. This reddish brown discoloration normally signals that the lift chains have not been properly lubricated. If this situation has occurred, it is extremely important to lubricate the lift chains immediately.

All through lift chain operation it is common for some metal to metal contact to occur that could cause some parts to wear out in due course. When there is 3% elongation on the lift chain, it is considered by industry standards to have worn out the chain. So as to stop the scary likelihood of a disastrous lift chain failure from occurring, the manufacturer highly recommends that the lift chain be replaced before it reaches 3% elongation. The lift chain gets longer because of progressive joint wear which elongates the chain pitch. This elongation could be measured by placing a certain number of pitches under tension.

To be able to ensure correct lift chain maintenance, another factor to think about is to check the clevis pins on the lift chain for signs of wearing. Lift chains are assembled so that the clevis pins have their tapered faces lined up with each other. Usually, rotation of the clevis pins is commonly caused by shock loading. Shock loading happens if the chain is loose and then all of a sudden a load is applied. This causes the chain to go through a shock as it 'snaps' under the load tension. Without the correct lubrication, in this particular case, the pins can rotate in the chain's link. If this particular scenario happens, the lift chains should be replaced immediately. It is vital to always replace the lift chains in pairs so as to ensure even wear.


Click to Download the pdf

Forklift Parts

Attachments for Gradall Forklift

Attachments for Gradall Forklifts - Throughout the period when World War II caused a shortage of laborers, the famous Gradall excavator was established in the 1940s as the creation of two brothers Koop and Ray Ferwerda. Partners in a Cleveland, Surprise construction business called Ferwerda-Werba-Ferwerda, the brothers faced a huge predicament when a lot of men left the workforce and...

More

---

Parts for Hydraulic Boom Lifts

Hydraulic Boom Lift Part - Telehandlers or Shooting Forklift Booms Shooting forklift booms may also be known as telescopic booms or telehandlers and are very useful on rough terrains. This particular type of boom could hoist staff to heights of twenty to forty feet. These booms are normally utilized outside on construction sites or within the agricultural industry. Booms Must...

More

---

Parts for Rough Terrain Forklift

Parts for Rough Terrain Forklifts - There are in fact two different classifications of lift trucks within the materials handling market, the industrial model and the rough terrain model. Rough terrain lift trucks first arrived on the marketplace in the 1940's and were primarily utilized on rough roads, perfect for areas where no paved roads were available, like building sites...

More

---

Attachment for Knuckle Boom

Knuckle Boom Attachments - Businesses usually have to carry, transfer, and stock up extremely heavy cargo. Load sizes from 5 to 10 tons which have to be transferred using dependable equipment that could load and support itself. To resolve these issues, very large Boom Trucks were invented so as to do these huge jobs. There are lots of various models...

More

---

Parts for Stacker Forklift

Stacker Forklift Parts - A type of compact forklift, the electric stacker is used to work in smaller areas, making loading and lifting a lot easier on the warehouse worker. Normally wide, but flat objects like tubes, slabs and pallets are transported using this piece of equipment. There are metallic prongs jutting out horizontally from the body of the electrical...

More

---

Crown Forklift Parts

Crown Forklift Part - The Crown company was founded in 1945 by two brothers, Allen A. Dicke and the late Carl H. Dicke. Carl's son and Chairman Emeritus, James F. Dicke, joined the family business later on that same year. Presently, his son, James F. Dicke II, is Chairman and CEO. James F. Dicke III, serves as the company Head...

More

---

Parts for Walkie Stackers

Parts for Walkie Stacker - A pallet stacker is a type of pallet jack that is employed to transport, stack and lift palletized goods that are overly heavy for manual lifting. Its main purpose is to load and unload pallets on trucks, and also transferring pallets to and from a variety of places within a storeroom space or warehouse. For...

More

---

Parts for Gas Forklift

Part for Gas Forklift - In the year 1893, inventor Rudolf Diesel developed the diesel engine. The combustion engine functions by providing the heat of compression in order to burn the fuel and initiate ignition. Then the fuel is injected into the combustion chamber. This design is in contrast to spark ignition engines, like for instance gasoline or petrol engines...

More

---